6 Different Types Of Calipers and Their Uses

Types Of Calipers

Calipers are measurement tools that are used to measure the complex dimensions of an object where a ruler, tape measure, or any other measurement tool cannot be used. These dimensions include the depth, internal and external measurements.

They are also preferred for measurement by engineers and woodworkers because they give very precise readings. However, the tools come in different types and these are listed down below.

Types of Calipers

1. Digital Caliper

Digital Caliper

Photo: thearchitectsguide.com

Digital calipers offer the latest in caliper measurement technology. Though they have ruler scales on the front side with measurements in cm, mm or inches, this is rarely used to take the readings.

Instead, the unit incorporates the use of a Printed Circuit Board (PCB) strip with copper lines, which is laid out below the ruler scale and it runs through the entire length of the slide beam. The reading head also has a PCB with its own copper lines.

The combinations of these two copper line patterns create a variable capacitor, which comes into action as you slide the head over the ruler scale.

A microprocessor in the head calculates the difference in this capacitance then converts it into a measurement reading then displays it on an LCD screen. This makes it very easy to use because it does the measurement and calculation for you, and gives the most accurate reading on screen.

For convenience, these tools have buttons for switching the measurement units, say from inches to mm, and zero setting functionality for eliminating the zero error or setting the reading to zero at any distance.

Other than that, the tool has a very similar appearance to a Vernier caliper, having inside and outside measuring jaws, and a depth bar for depth measurement. However, it is costlier because of the technology used.

2. Vernier Caliper

Vernier Caliper

As stated earlier, a Vernier caliper has a very similar design to a digital caliper but lacks an electronic measuring system and an LCD screen. However, it is equipped with inner and outside measuring jaws, as well as a depth bar for depth measurements.

This tool usually has imperial (inches) and metric (millimeters) scales and utilizes a movable graduated scale to get the measurement precisely down to the fractional level. As such, it can give readings accurately to 0.01mm while normal scales usually go down to 0.1mm.

3. Dial Caliper

Dial Caliper

Photo: bestconsumerreviews.com

Dial calipers do have a main scale like in Vernier calipers but the movable scale is in the form of a dial. This dial makes it a bit easier to use because it has a pointer that shows the reading to the hundredths of a millimeter.

The main scale gives the reading in whole decimal numbers and combines with the dial to give measurement readings with a resolution of 0.01. That said, this caliper has a depth bar, inner and outer jaws for measuring the depth, inner and outer lengths of objects.

4. Jenny Caliper

Jenny Caliper

Photo: etsy.com

This tool is also called an odd leg or a hermaphrodite caliper and is very similar to a divider. This is because it works by pinning its sharp end to a fixed location on the surface while the other end measures the distance to the side/part of an object from the pinned point.

Some jenny calipers have a scriber on the measurement end, which can be used to make marks at a particular distance. However, it doesn’t have a built-in scale. You have to transfer the measured distance to a ruler to get a reading.

5. Spring Joint Caliper

Spring Joint Caliper

Photo: shop.ellisantique.com

A spring joint caliper comes in 3 types: an inside caliper with outward-facing jaws for taking inner measurements, an outside caliper with inner facing jaws for taking outer measurements, and a divider caliper for measuring between two spots on a flat surface.

Regardless of the type, they have a common functional design, which includes the two legs/jaws, a spring that pulls them towards each other, and an adjustment screw/nut.

Measurements are taken by adjusting the screw to the point that the jaws contact the outer/inner surface of an object or the points on the flat surface.

The C spring at the top maintains tension on the legs while the screw holds them steady in position. This ensures they don’t move and results in zero errors as you check the measurement against a ruler. As such, this caliper is slightly better than a jenny caliper.

6. Micrometer


Micrometers are also available in different types such as inside, outside, depth, inch, and metric micrometers. As the name suggests, they measure in microns (to the hundredths of a millimeter), which helps to enhance accuracy.

The measuring section is opened up by turning the knob on the thimble and this opens up the scale on the barrel. This barrel scale gives the reading in whole numbers while the thimble scale gives the measurement as a decimal value to two decimal places.

Combined, you get accurate readings with a resolution of 0.01mm. However, this caliper is only ideal for measuring small distances.


As a summary, calipers are must-have tools for carpenters and engineers due to their precision measurement capabilities. Though expensive, digital calipers are the easiest to use because they have digital readouts and are flexible enough to take inner, outer, and depth measurements.

Thanks for letting us know!
Was this page helpful?
Related Reads
A nail puller comes handy in woodworking tasks, somewhere or the else. With the best nail puller, ...
A wood chisel is a handy and readily used tool in woodworking. It has a shaped blade on its end that ...
What We Like Powerful 3/4 HP induction motor Motor overload protection for enhanced durability ...
Wood routers are some of the most versatile tools available today for professional, hobbyist, and ...
Jointers are considered essential woodworker tools because of the value they create for your ...
Jobsite radios are invaluable sources of worksite entertainment that can transform your experiences ...
For any woodworker, whether a beginner professional, straightening and smoothing boards is an ...
A jointer is always the tool to turn to when you need to prepare wood piece edges and the planer is ...
Staple guns will come in handy for a wide variety of projects for DIYers, hobbyists, and ...